GEN 3 (2022+) Wheels and Tires Photo thread

Stock non TRD suspension no rubbing at all, watched a vid on yt, and apparently you can fit 35's with very minor cutting of inner fender plastic and -18mm offset

 

Do you need to use hubcentric rings with aftermarket wheels? Just curious what everyone is doing.

 

Yes if the hub diameter do not match, most times the wheels do

 

I ordered an aluminum set, box says 95.1 to 106.1, ring says 95.1 to 106…grrr, lol

 

Cheap (and also dirty, sorry) SR5 with cheap eBay 295/70/18 on AGP replica rims.

 

got factory 3” lift , amp power steps, method wheels 295/70/18 (34.26) no rubbing or anything not even close ! +18 offset

Also I remember someone asking about the spare , I have a full size spare it fits btw , a bit off center though , I’ll have to look into that lol

 

11.50s Fits the stock wheel perfectly with no rubbing. I went back and forth a million times about 12.50s and just decided an inch didn’t matter that much to me

 

I'm torn... I got a black tundra with no chrome.. do I go for the blacked out look with black wheels. Either a set of the TRD Pro BBS or Methods 18". Or do I go bronze wheels. Would be a 18 method for sure...

Going with a 35x12.5.. maybe 37 if I can fit it.

Opinions Welcomed!

 

Here’s a shot of the blacked out look of my Nightshade Blueprint Limited with TRD Pro wheels to compare…

 

After browsing and over analyzing everything in this forum and elsewhere, pulled the trigger on a set of Method 705 in 17x8.5 ET0 and Toyo RT Trails 35x12.50/17. With no lift, I did have to do the usual liner trimming, bracket and mudflap removal but so far so good. Went camping immediately after the install and got some much needed dirt therapy.

 

35X12.5r18 KO2's mounted up finally. No rubbing at all, lock to lock.

 

Looking good
Stock height or levelled ?

 

Does the TRD Pro come with a higher stance?

 

1.1” in the front.

 

Thanks!

Stock height / Factory Pro Fox Suspension has a level from factory up front.

 

After digging through this for a few months ended up pulling the trigger on Method 318 8.5x18 +40 with KO2 295/70R18's. No mods other than larger after market mud flaps, no rubbing lock to lock anf the tires are flush with the off road stock fender flares. I live up in the mountains of CO on dirt roads so I can't have any poke, this fit the requirements perfectly. Now to figure out what pressure to run, starting off at 36psi, the math works out to 31 but I don't think I should keep them that low.

 

Looks good, fitment is best for that type of terrain. Method wheels sure seem popular lately.

 

Yah they were cheap and quick to get, I really wanted some gram-lites but the lead time was insane. The hard part is finding high offset wheels over +35. This was one of them.

 

I had a set of wheels I ordered in March not going to ship mid to late June at the earliest. I passed once I realized how much poke there was gonna be.

 

Good taste. Bronze and black is always a killer match

 

Nice setup.

 

I have the TRD Off Road wheels, which I think are the same offset as yours, and no lift or suspension mods. I am running 275/65-20 BFG's, which is basically a 34 inch tire. No rubbing whatsoever. Nice thing is they also just barely fit in the spare carrier if you're into running a full size spare and a 5-tire rotation, which I am. A lot of people run 295/60-20, which is actually ever so slightly smaller in diameter, but wider, of course, and claim no rub. (It looked to me like 295s would be a little tight on the front of the upper control arms at full lock and in compression, but it's hard to visualize how the arm and the tire move relative to one another.)

 

w ~1k payload

 

That thing is sweet.

 

2022 TRD sport ( sits 1/2” lower in front.) Factory TRD 20” rims. Going to do the Westcott lift down the road. For now can I fit 295/65-20 on the truck stock? Does the 1/2” lower in the front matter? No mud flaps. Thanks.

 

Falkens Wildpeaks, 35x12.5x18

 

I ordered Toyo at3 and the next day I got an email saying they were back order and my other option is nitto recon grappler? Who’s running them ? Are quiet on hwy ? I’m currently on ko2 stock size and wanting go 285/65/20 (34.6). I find them really quiet will I be disappointed as far as road noise goes ?

 

Yeah, I love these tires so far, Ive had Toyos MT before, and those were loud. But its quiet, tread wear is great too

 

Been debating which tire to go with since I bought my 24 limited 2 months ago. I finally pulled the trigger and went with 285/60/20 Falken Wilpeaks AT4W. They were actually $5.00 cheaper per wheel than the popular AT3's. They should be delivering to the installer by saturday.

 

I hear the AT3 are quieter than the Recons.